Hello: Am trying to configure my bridge according to instructions on Tor site. Using Ubuntu. No matter what port I pick for the ORPort I keep getting this error:
Unable to find IPv4 address for ORPort 80. You might want to specify IPv4Only to it or set an explicit address or set Address.
Have never seen this before. Please help. Thanks
On 15.02.2021 21:00, Anonforpeace wr
Unable to find IPv4 address for ORPort 80. You might want to specify IPv4Only to it or set an explicit address or set Address.
^^^^^^^^^^ Have you upgraded to a 0.4.5.n version? (New IPv6 address discovery) Is explained here: https://www.mail-archive.com/tor-relays@lists.torproject.org/msg17760.html 'ORPort 9001 IPv4Only'
Thank you for this! I'm back online!
Sent from ProtonMail mobile
-------- Original Message -------- On Feb 17, 2021, 6:19 PM, wrote:
On 15.02.2021 21:00, Anonforpeace wr
Unable to find IPv4 address for ORPort 80. You might want to specify IPv4Only to it or set an explicit address or set Address.
^^^^^^^^^^ Have you upgraded to a 0.4.5.n version? (New IPv6 address discovery) Is explained here: https://www.mail-archive.com/tor-relays@lists.torproject.org/msg17760.html 'ORPort 9001 IPv4Only'
-- ╰_╯ Ciao Marco!
Debian GNU/Linux
It's free software and it gives you freedom! _______________________________________________ tor-relays mailing list tor-relays@lists.torproject.org https://lists.torproject.org/cgi-bin/mailman/listinfo/tor-relays
I'm used to seeing many connections on my middle and bridge nodes, but on the new Exit node in NYX I'm seeing ~850 inbound connections and 0 outbound connections, this seems strange. Googling isn't getting me very far, whats with this behavior?
I'm not sure how TOR gets its addresses but sometimes you need to specify it directly, especially for bridges for some reason. Just use your whole IP
ORPort 123.456.789.123:80
Dont forget if you are mapping Obfs4 you need to add the permissions so obfs can go to a port that low
/Don't forget to change the |ORPort|, |ServerTransportListenAddr|, |ContactInfo|, and |Nickname| options./
//
*
/If you decide to use a fixed obfs4 port smaller than 1024 (for example 80 or 443), you will need to give obfs4 |CAP_NET_BIND_SERVICE| capabilities to bind the port with a non-root user:/
/|sudo setcap cap_net_bind_service=+ep /usr/bin/obfs4proxy|/
/To work around systemd hardening, you will also need to set |NoNewPrivileges=no| in |/lib/systemd/system/tor@default.service| and |/lib/systemd/system/tor@.service| and then run |systemctl daemon-reload|. For more details, see ticket 18356 https://gitlab.torproject.org/tpo/core/tor/-/issues/18356./
*
/Note that both Tor's OR port and its obfs4 port must be reachable. If your bridge is behind a firewall or NAT, make sure to open both ports. You can use our reachability test https://bridges.torproject.org/scan/ to see if your obfs4 port is reachable from the Internet./
On 2/15/2021 3:00 PM, Anonforpeace wrote:
Hello: Am trying to configure my bridge according to instructions on Tor site. Using Ubuntu. No matter what port I pick for the ORPort I keep getting this error:
Unable to find IPv4 address for ORPort 80. You might want to specify IPv4Only to it or set an explicit address or set Address.
Have never seen this before. Please help. Thanks
tor-relays mailing list tor-relays@lists.torproject.org https://lists.torproject.org/cgi-bin/mailman/listinfo/tor-relays
tor-relays@lists.torproject.org
-
Anonforpeace -
Astroskis Lists -
lists＠for-privacy.net